|
|
|
|
|
MBD-PDSMi+-O |
- PDSMi+ (Standard Retail Pack)
|
MBD-PDSMi+-B |
|
|
|
Form Factor |
|
Dimensions |
- 12.0" width x 9.6 " length , (30.5cm x 24.4cm), 6 layer PCB
|
|
|
CPU |
- Single LGA775 ZIF Socket
- Supports a Quad-Core Intel® Xeon® 3200 series processor
- Supports a Dual-Core Intel® Xeon® 3000 series processor
- Supports a Quad-Core Intel® Core™2 Extreme series processor
- Supports an Intel® Core™2 Quad series processor
- Supports an Intel® Core™2 Duo series processor
- Supports an Intel® Pentium® processor E2000 series
- Supports a Dual-Core Intel® Pentium® D processor
- Supports an Intel® Pentium® Extreme Edition processor
- Supports an Intel® Pentium® 4 processor
- Supports an Intel® Celeron® processor E1000 series
- Supports an Intel® Celeron® processor 400 series
- NOTE: This board DOES NOT support Q9000, E8000, E7000, E5000 series or 45nm processor
|
System Bus |
- 1066 / 800 / 533 MHz system bus
|
|
|
Memory Capacity |
- Four 240-pin DIMM sockets
- Supports up to 8 GB of memory (Single / Dual Channel)
|
Memory Type |
- DDR2 667/533MHz unbuffered, ECC / non-ECC SDRAM, 240-pin gold-plated DIMMs
|
DIMM Sizes |
- 256 MB, 512 MB, 1 GB, 2GB
|
Memory Voltage |
|
|
|
Chipset |
- Intel 3000 (Mukilteo-2) chipset
- ICH7R + PXH-V + Intel® 82573V + Intel® 82573L
|
Serial ATA |
- Intel® ICH7R SATA2 (3 Gbps) controller built-in
- Intel:
RAID 0, 1, 5, 10 support (Windows Only) - Adaptec:
RAID 0 (Two, three, four drives only)
RAID 1 (Two hard drives only)
|
IPMI |
|
Network Controllers |
- 1x Intel® 82573V Gigabit PCI-Express Ethernet
- 1x Intel® 82573L Gigabit PCI-Express Ethernet
- Supports 10Base-T, 100Base-TX, 1000BASE-T, RJ45 output
|
VGA |
- On-board ATI ES1000 16MB graphics
|
Super I/O |
|
Clock Generator |
|
|
|
Serial ATA |
- Four Serial ATA ports (3 Gbps performance)
- Four SATA hard drives supported
|
IDE |
- One EIDE channel supports up to two UDMA IDE devices
- IDE Master / Slave 2 ports
- Supports UDMA Mode 5, PIO Mode 4, and ATA/100
- White Connector for Compact Flash (CF, 40-pin IDE connector) card only
|
Floppy |
- 1 Floppy controller; 1.44 MB
|
LAN |
|
USB |
- Up to 6x USB 2.0 compliant / 1.1 compatible ports
- 4x Internal USB headers
- 2x Rear USB ports
|
VGA |
|
Keyboard / Mouse |
- PS/2 keyboard and mouse ports
|
Serial Ports |
- 1x Fast UART 16550 serial port
- 1x Header
|
Parallel Port |
- 1x ECP / EEP Parallel Header
|
|
|
|
|
4U / Tower |
|
Important Note |
- To ensure system stability, a ATX power supply w/ 4A (minimum) on 5V Standby is required
- Only Supermicro 1U chassis is recommended for 1U Building Block Solutions
|
|
|
Universal Slot |
- 1 (x8) PCI-Express Slot (via Riser Card) OR
- 1x 64-bit PCI-X 133MHz Slot (via Riser Card)
|
PCI |
- 1x 32-bit 33MHz PCI (3.3V) slot
|
|
|
BIOS Type |
- 8Mb Flash EEPROM with Phoenix BIOS®
|
BIOS Features |
- Plug and Play (PnP)
- DMI 2.3 support
- PCI 2.2
- ACPI 1.0
- USB Keyboard support
- SMBIOS 2.3
|
|
|
Software |
- Optional IPMI (Intelligent Platform Management Interface) 2.0
- SuperDoctor® III
- Watch Dog
- NMI
|
Power Configurations |
- ACPI/APM Power Management
- Main Switch Override Mechanism
- Wake-On-Ring (WOR) header
- Wake-On-LAN (WOL) header
- Power-on mode control for AC power loss recovery
- Internal / External Modem Rign-on
|
|
|
Voltage |
- Monitors for CPU Cores (+1.8V, +3.3V, +5, ±12V, +3.3V/+5V Standby, VBAT)
- CPU Core 4-Phase-switching voltage regulator with auto-sense from 0.8375V-1.6000V
- Adjustable CPU clock frequency ratio
|
FAN |
- Fan Speed Control
- Total of six 4-pin fan headers
- 6x fans with tachometer monitoring
- Status monitor with firmware speed control
- Low noise fan speed control
- Status monitor for on/off control
- Support 3-pin fans (without speed control)
- Pulse Width Modulated (PWM) fan connector
|
Temperature |
- Monitoring for CPU and chassis environment
- CPU thermal trip support
- Thermal Monitor (TM2) Support
|
LED |
- CPU / System Overheat LED
- +5V Standby Alert LED
- Suspend-state indicator LED
|
Other Features |
- Chassis Intrusion Detection
- Chassis Intrusion Header
|
|
|
RoHS
|
|
Environmental Spec. |
- Operating Temperature: 10°to 35°C (50°to 95°F)
- Non-operating Temperature: -40°to 70°C (-40°to 158°F)
- Operating Relative Humidity: 8% to 90% (non-condensing)
- Non-operating Relative Humidity: 5 to 95% (non-condensing)
|
|
|
FCC |
- Passed to meet FCC standard requirement
| |
|
|
Part Number |
Qty |
Description |
PDSMi+ |
MBD-PDSMi+-O |
1 |
PDSMi+ Motherboard |
Manual(s) |
MNL-0889 |
1 |
Motherboard Manual for PDSMi+ |
I/O Cables |
CBL-0022L
CBL-0036L-03
CBL-0044L |
1 1
4 |
ATX Floppy Cable ATA 66/100 IDE LP Cable SATA Cable (2Ft.) |
Driver Disk |
CDR-PD |
1 |
Version 1.20 (or newer) CD |
I/O Shield |
CSE-PT07L |
1 |
I/O Shield for PDSMi+ |
|
|
|
|
|
|
Part Number |
Qty |
Description |
Heat Sink |
SNK-P0016 |
- |
1U, Pentium® D LGA775, Passive Heatsink |
Riser Card |
CSE-RR1U-Xi
CSE-RR1U-ELi |
- - |
1U 64-bit PCI-X Riser Card for PDSMi+ (Full height, full length) 1U Universal (SXB-E) Slot to PCI-E Slot Riser Card for PDSMi+ | | |
|
|
|
|
|
|
|
Key Features
Key Features
1. Intel® Xeon® 3200 / 3000 Series,
Core™ 2 Quad / Duo / Extreme Series,
Pentium® D, Pentium Extreme Edition,
Pentium 4 & Celeron D in LGA775
Package (FSB 1066/800/533)
2. Intel® 3000 (Mukilteo-2) Chipset
3. Up to 8GB unbuffered ECC / non-ECC DDR2 667/533MHz SDRAM
4. 1x Intel® 82573L PCI-e Gigabit LAN 1x Intel® 82573V PCI-e Gigabit LAN
5. Built-in SATA Controller 4x SATA (3 Gbps) Drive with RAID 0, 1, 5, 10 Support
6. 1 (x8) PCI-Express or 1x 64-bit 133MHz PCI-X, 1x 32-bit 33MHz PCI
7. On board ATI ES1000 Graphics
8. IPMI 2.0 Support (AOC-IPMI20-E)
|
|
|
|
|
|
|