 |
|
MBD-X8DTU-LN4F+ |
|
| |
|
|
| Form
Factor |
|
|
Dimensions |
- 12.8" x 16.5" (32.5cm x 41.9cm)
|
| |
|
|
| CPU |
- Dual 1366-pin LGA Sockets
- Supports up to two Intel® 64-bit
Xeon® processor(s) of the same type below:
- Intel®
Xeon®Processor 5600 Series (Westmere)
- Intel®
Xeon®Processor 5500 Series (Nehalem-EP)
|
| QPI |
|
| |
|
|
| Memory
Capacity |
- 18x 240-pin DIMM sockets
- Supports up to 288GB 1333 / 1066 / 800MHz
DDR3 ECC Registered memory
- Supports up to 48GB 1333 / 1066 / 800MHz
DDR3 ECC / Non ECC Unbuffered memory
- Memory Mirroring supported
|
| Memory
Type |
- 1333 / 1066 / 800MHz ECC Registered / ECC
or Non ECC Unbuffered DDR3 SDRAM 72-bit, 240-pin gold-plated
DIMMs
|
| DIMM
Sizes |
- 1GB, 2GB, 4GB , 8GB , 16GB
|
| Memory
Voltage |
|
| Error
Detection |
- Corrects single-bit errors
- Detects double-bit errors (using ECC
memory)
- Supports Intel® x4 and x8 Single Device
Data Correction (SDDC)
|
| Note: |
This board does not
support LRDIMM memory. Please refer to
HERE for list of motherboards with LRDIMM support. |
| |
|
|
|
Chipset |
- Intel® 5520 (Tylersburg) chipset
- ICH10R + IOH-36D
|
| SATA |
- Intel ICH10R SATA 3.0Gbps Controller
- RAID 0, 1, 5, 10 support (Windows)
- RAID 0, 1, 10 support (Linux)
|
| IPMI |
- Support for Intelligent Platform Management
Interface v.2.0
- IPMI 2.0 with virtual media over LAN and
KVM-over-LAN support
- Winbond® WPCM450 BMC
|
|
Network Controllers |
- 2x Intel® 82576 Dual-Port Gigabit Ethernet
Controllers (4 ports)
- Supports 10BASE-T, 100BASE-TX, and
1000BASE-T, RJ45 output
- Intel® I/OAT 3 support for
fast, scaleable, and reliable networking
- VMDq support for better
performance of virtualization
- 1x Realtek RTL8201N PHY (dedicated IPMI)
|
|
Graphics |
|
| Super
I/O |
|
| |
|
|
| Serial
ATA |
- Six Serial ATA ports
- Six SATA hard drives supported
|
| LAN |
- 4x RJ45 LAN ports
- 1x RJ45 Dedicated IPMI LAN port
|
| USB |
- 2x USB rear ports
- 1x USB on-board
- 5x USB internal headers
- Total 8 USB 2.0 Compliant
|
| VGA |
|
|
Keyboard / Mouse |
- PS/2 keyboard and mouse ports
|
| Serial
Port / Header |
- 1 Fast UART 16550 serial port
- 1 Fast UART 16550 serial header
|
|
 |
|
|
|
|
|
Important Chassis Notes |
- To support the new generation Intel® Xeon®
processor-based motherboards, a
Revision K chassis is
recommended for most models. Please talk to your sales
representative or follow the link for details.
|
| |
|
|
| PCI-Express / PCI-X /
UIO |
Left Side
- 1 (x16) PCI-E 2.0 + 1 PCI-E
2.0 x4 by riser card
Right Side
- 1 (x8) PCI-E 2.0 + 1 PCI-E 2.0 x4 by riser
card
- For 2U configuration, Please go to
UIO Riser Cards page
|
| |
|
|
| BIOS
Type |
- 32Mb SPI Flash EEPROM with AMI® BIOS
|
| BIOS
Features |
- Plug and Play (PnP)
- PCI 2.2
- ACPI up to 3.0
- USB Keyboard support
|
| |
|
|
|
Software |
- IPMI (Intelligent Platform Management
Interface) v1.5 / 2.0 with KVM support
-
SuperDoctor® III
|
| Power
Configurations |
- ACPI / ACPM Power Management
|
| |
|
|
|
Voltage |
- Monitors for CPU Cores, +1.8V, +3.3V, +5V,
+12V, +3.3V Standby, +5V Standby, VBAT, Memory, Chipset
Voltages.
- 6-Phase-switching voltage regulator
|
| FAN |
- Total of eight fan headers supporting up to
8 fans
- Eight 4-pin fan headers
- 8x fans with tachometer status monitoring
- Support 3-pin fans (w/o speed control)
- Low noise fan speed control (4-pin fan
only)
|
|
Temperature |
- Monitoring for CPU and chassis environment
- Thermal Control for 8x fan connectors
- PECI
|
| Other
Features |
- Chassis intrusion detection
- Chassis intrusion header
|
| |
|
|
RoHS
|
|
|
Environmental Spec. |
- Operating Temperature: 10° to 35° C (50° to
95°F)
- Non-operating Temperature: -40° to 70° C
(-40° to 158° F)
- Operating Relative Humidity: 8% to 90%
(non-condensing)
- Non-operating Relative Humidity: 5 to 95%
(non-condensing)
|
|