|
 |
| Form Factor |
|
| Dimensions |
- 12" x 9.5 " (30.5cm x 24.0cm)
|
| |
|
|
| CPU |
- Single LGA775 (Prescott) ZIF Socket
- Supports an Intel® Pentium® 4 processor 6x0 or 5x0 sequence on 90nm process ONLY (800MHz FSB) or
- Supports an Intel® Celeron® processor with 256KB L2 Cache (533MHz FSB)
- Hyper-Threading (HT) enabled
|
| System Bus |
|
| Operating System Software |
|
| |
|
|
| Memory Capacity |
- Four 240-pin DIMM sockets
- Supports up to 4 GB DDR2 400 / 533MHz unbuffered ECC or Non-ECC memory
- Dual channel memory bus
- Memory must be populated in pairs
|
| Memory Type |
- DDR2 400 / 533MHz unbuffered ECC or Non-ECC SDRAM 72-bit, 240-pin gold-plated DIMMs
|
| DIMM Sizes |
- 256MB, 512MB, 1GB
-
Unbuffered ECC / non-ECC DDR2
- Total 256MB to 4GB memory
|
| Memory Voltage |
|
| Error Detection |
- Corrects single-bit errors
- Detects double-bit errors (using ECC memory)
|
| |
|
|
| Chipset |
- Intel E7221 (Copper River) chipset
- ICH6R + FWH + BCM5721
|
| Serial ATA |
- Intel® ICH6R SATA controller
- RAID 0, 1, JBOD support
|
| SCSI |
- Adaptec AIC-7902 Controller
- Dual-Channel Ultra320 SCSI (Host RAID only supports 4 drives)
- Host RAID 0, 1, 10, JBOD support
|
| RAID |
- Support for Zero-Channel RAID
- Optional: (Card not included)
|
| IPMI |
|
| Network Controllers |
- 2x Broadcom BCM5721 Gigabit Ethernet Controllers
- Supports 10/100/1000BASE-T, RJ45 output
|
| Graphics |
- Onboard integrated server quality graphics in MCH
|
| Super I/O |
|
| |
|
|
| Serial ATA |
- Four Serial ATA ports
- Four SATA hard drives supported
|
| IDE |
- One EIDE channel supports up to two UDMA IDE devices
- Supports UDMA Mode 5, and ATA/100
|
| Floppy |
- 1 Floppy controller; 1.44 MB, 2.88 MB, 3-mode support
|
| Infrared |
|
| LAN |
|
| USB |
- 2x USB 2.0 / 1.1 ports
- 4x USB 2.0 / 1.1 header for 4x ports
|
| VGA |
|
| Keyboard / Mouse |
- PS/2 keyboard and mouse ports
|
| Serial Ports |
- 1x Fast UART 16550 serial ports
- 1x serial header
|
| Parallel Port |
- 1x ECP / EEP Parallel Port
|
|
 |
|
|
| 1U |
|
| Important Note |
- To ensure system stability, a 300W (minimum) ATX power supply [4-pin +12V AND (20 or 24-pin)] is required.
|
| |
|
|
| PCI-Express |
|
| PCI-X |
- 1x 64-bit 100MHz PCI-X (3.3V) slot
|
| PCI |
- 1x 32-bit 33MHz PCI (5V) slot
|
| |
|
|
| BIOS Type |
- 8Mb Flash EEPROM with AwardBIOS®
|
| BIOS Features |
- Plug and Play (PnP)
- PCI 2.2
- ACPI 1.0
- USB Keyboard support
|
| |
|
|
| Software |
- Optional IPMI (Intelligent Platform Management Interface) 2.0
- SuperDoctor® III
- Watch Dog
- NMI
|
| Power Configurations |
- ACPI/APM Power Management
- Wake-On-Ring (WOR) header
- Wake-On-LAN (WOL) header
- Keyboard Wakeup from Soft-Off
- Power-on mode control for AC power loss recovery
- Internal/External modem remote ring-on
|
| |
|
|
| Voltage |
- Monitors for CPU Cores, +1.8V, +3.3V, +5, ±12V, +5V Standby
- CPU Core 4-Phase-switching voltage regulator with auto-sense from 0.8375V-1.6000V
|
| FAN |
- Total of five 3-pin fan headers
- 5x fans with tachometer monitoring
- Status monitor with firmware / software speed control
- Support 3-pin fans
|
| Temperature |
- Monitoring for CPU and chassis environment
- CPU thermal trip support
- Thermal control for 5x fan connectors
- I2C temperature sensing logic
|
| LED |
- CPU / System Overheat LED
- +5V standby alert LED
|
| Other Features |
- Chassis intrusion detection
- Chassis intrusion header
|
|